| Item # |
Description |
Part # |
| 1 |
Blower Motor (with Gasket) |
7250P-085 |
| 2 |
926 Control Board Upgrade Kit
- For units built before July, 2008 that have the 925 Control Board
- Includes 926 Control Board (with Fuse) 7350P-008, Display Card and Ribbon Cable 64980136 (old # 7350P-009), Spark Cable 7250P-653, Hold Down Clips 7250P-352, and Flue Jumper Wire (if needed).
|
7250P-731
(also use 7250P-1014) |
| 3 |
Relief Valve |
7250P-080 |
| 4 |
Thermistor Inlet / Outlet |
7250P-059 |
| 5 |
Water Pressure Switch (red dot, most common) |
7250P-081 |
| |
Water Pressure Switch (blue dot, less common) |
7250P-096 |
| 6 |
ECO High Limit |
7250P-019 |
| 7 |
Thermodisc Flue ECO - 210 Degree |
7250P-089 |
| 8 |
Spark Electrode (with Gasket)
|
7250P-058 |
| 9 |
NIT Burner (with Gasket) |
7250P-248 |
| 10 |
Flame Rectification Probe |
7250P-049 |
| 11 |
Gas Valve (Dungs)
- Earlier units had a Honeywell Gas Valve. If so, please order the Dungs Gas Valve as well as the 7250P-645 Honeywell-to-Dungs Adapter Kit.
|
7250P-449 |
| 12 |
LED Display Box with Ribbon Cable - DISCONTINUED
- For original 925 Control Board only. If you have already upgraded to a 926 Control Board, order the Display Board for 926 Control Board 64980136 (old # 7350P-009).
|
7250P-332 |
| 13 |
Control Board Fuse (110 Volt, 6.3 Amp) |
7250P-378 |
| 14 |
Low Voltage Wiring Harness (10 Pin / 20 Pin) |
7250P-376 |
| 15 |
9 Pin Wiring Harness (120 Volt) |
7250P-387 |
| 16 |
5 Pin Wiring Harness (120 Volt) |
Old # 7250P-390, replace with 7250P-696. |
| 17 |
Spark Cable |
Old # 7250P-392, replace with 7250P-653. |
| 18 |
Burner Door Ceramic Refractory |
7250P-161 |
| 19 |
Ceramic Target Wall |
7250P-160 |
| 20 |
Burner Gasket |
7250P-070 |
| 21 |
Burner Door |
7250P-169 |
| 22 |
Gasket for Spark Electrode and Flame Rectification Probe |
7250P-005 |
| 23 |
Screw for Spark Electrode and Flame Rectification Probe |
7250P-069 |
| Other Parts: (not shown) |
| |
Honeywell Gas Valve Conversion Kit (Natural Gas to Propane) |
7250P-138 |
| |
Air Inlet Baffle |
7250P-145 |
| |
Blocked Vent Pressure Switch |
7250P-150 (new # 64980007) |
| |
Gasket (Burner Door to Air Channel) |
7250P-170 |
| |
Temperature / Pressure Gauge - 60 PSI |
7250P-211 |
| |
Blower Motor Gasket |
7250P-226 |
| |
PC Connection Cable |
7250P-320 |
| |
Control Board Clips (not shown) |
7250P-352 |
| |
Condensate Hose Assembly |
7250P-460 |
| |
Temperature / Pressure Gauge - 200 PSI |
7250P-499 |
| |
Adapter Plate (Dungs Gas Valve to Blower Motor) |
7250P-644 (new # 64980046) |
| |
Gas Valve Change Out Kit - Honeywell to Dungs |
7250P-645 |
| |
Dungs Gas Valve Conversion Kit (Natural Gas to Propane) |
7250P-714 |
| |
Dungs Gas Valve Conversion Kit (Propane to Natural Gas) |
7250P-715 |
| |
Screw M4 x 20MM for Swirl Plate (Dungs Gas Valve) |
64980287 (old # 7250P-717) |
| |
PC Connection Cable with USB Connector |
7250P-738 |
| |
926 Control Board
- Only purchase if the control board has previously been replaced with a 926 board
|
7350P-008 |
| |
Display Board for 926 Control
- Only purchase if the control board has previously been replaced with a 926 board
|
7350P-009 (new # 64980136) |
| |
Condensate Neutralizer (formerly part # N1100) |
7450P-218 |
| |
Swirl Plate (for Dungs Gas Valve) |
7500P-092 (new # 64980049) |
| |
|
|
| |
See Accessories - PC connection, vent kits, mesh screens, etc. |
|
| . |
|
|
HA "High Altitude" Parts
* For HA designation, as indicated in model number (for example, T80M HA) |
| 8A* |
Flame Rectification Probe - location for the HA "High Altitude" unit. |
7250P-049 |
| 10A* |
Hot Surface Ignitor - location for the HA "High Altitude" unit. |
7250P-279 |
| 15* |
9 Pin Wiring Harness (120 Volt) - HA "High Altitude" |
7250P-386 |
| - |
Natural Gas to Propane Gas Conversion Kit (HA "High Altitude") |
7250P-714-1 |
| - |
Propane to Natural Gas Conversion Kit (HA "High Altitude") |
7250P-715-1 |
| |
|
|
